Cisco之中小企业网络（STP_HSRP）
STP（Spanning Tree Protocol），是生成树协议的缩写。在实际的网络环境中，经过物理链路备份能够实现链路的冗余，从而提升网络的可靠性。可是，交换网络会造成一个环路，根据交换机的转发原理（交换机向除接收端口以外的全部端口转发广播帧），会造成广播风暴，致使网络瘫痪。而STP协议正是用来解决二层环路的，STP协议经过一些特定的算法，在逻辑上阻塞一些端口，把一个环形的结构改变成一个逻辑上的树形结构，当正常通讯的线路出现故障时，被阻塞的端口会被从新激活，使数据可以从这条线路上正常传输。此协议在Cisco交换机上默认为开启。算法
HSRP（Hot Standby Router Protocol），热备份路由选择协议，是思科的一种私有协议。该协议中有多台路由器，对应一个HSPR组，该组只有一台路由器承担转发用户流量的职责，称为活跃路由器（路由器优先级最高，一般手工指定），另外一台为备份路由器。当活跃路由器失效时，备份路由器将承担全部流量的转发，成为新的活跃路由器，这就是热备份的原理。markdown
示例：公司内部网络拓朴图以下：网络
架构说明：架构
1）IP规划：负载均衡
vlan 10：172.16.10.0/24 网关：172.16.10.253dom
vlan 20：172.16.20.0/24 网关：172.16.20.253ssh
vlan 100：172.16.100.0/24 网关：172.16.100.253 （设备管理）spa
2）经过STP和HSRP实现VLAN间的负载均衡，奇数开始的VLAN以SW1为活跃路由器，以SW2为备份路由器。偶数开始的VLAN以SW2为活跃路由器，以SW1为备份路由器。即：router
SW1做为vlan10的活跃路由器，vlan20的备份路由器server
SW2做为vlan 20的活跃路由器，vlan10的备份路由器
配置以下：
1）配置基本信息：
ROUTER的配置信息：
ROUTER(config)#hostname ROUTER
ROUTER(config)#int f1/0
ROUTER(config-if)#ip add 172.16.1.5 255.255.255.252
ROUTER(config-if)#no sh
ROUTER(config-if)#int f0/0
ROUTER(config-if)#ip add 172.16.1.2 255.255.255.252
ROUTER(config-if)#no sh
ROUTER(config)#ip route 172.16.10.0 255.255.255.0 172.16.1.1
ROUTER(config)#ip route 172.16.20.0 255.255.255.0 172.16.1.1
ROUTER(config)#ip route 172.16.100.0 255.255.255.0 172.16.1.1
ROUTER(config)#ip route 172.16.10.0 255.255.255.0 172.16.1.6
ROUTER(config)#ip route 172.16.20.0 255.255.255.0 172.16.1.6
ROUTER(config)#ip route 172.16.100.0 255.255.255.0 172.16.1.6
ROUTER#wr
SW1的配置信息：
SW1(config)#hostname SW1
SW1(config)#ip routing
SW1(config)#int f1/8
SW1(config-if)#no switchport
SW1(config-if)#ip add 172.16.1.1 255.255.255.252
SW1(config-if)#no sh
SW1(config)#int range f1/5 - 6
SW1(config-if-range)#channel-group 1 mode on
SW1(config)#int range port-channel 1 , f1/0 - 1
SW1(config-if-range)#sw trunk encapsulation dot1q
SW1(config-if-range)#sw mo tr
SW1(config)#vlan 10
SW1(config-vlan)#vlan 20
SW1(config-vlan)#vlan 100
SW1(config)#vtp domain cisco
SW1(config)#vtp password cisco
SW1(config)#vtp mode server
SW1(config)#vtp pruning
SW1(config)#int vlan 100
SW1(config-if)#ip add 172.16.100.253 255.255.255.0
SW1(config-if)#no sh
SW1(config)#ip route 0.0.0.0 0.0.0.0 172.16.1.2
SW1#wr
SW2的配置信息：
SW2(config)#hostname SW2
SW2(config)#ip routing
SW2(config)#int f1/8
SW2(config-if)#no switchport
SW2(config-if)#ip add 172.16.1.6 255.255.255.252
SW2(config-if)#no sh
SW2(config)#int range f1/5 - 6
SW2(config-if-range)#channel-group 1 mode on
SW2(config)#int range port-channel 1 , f1/1 - 2
SW2(config-if-range)#sw trunk encapsulation dot1q
SW2(config-if-range)#sw mo tr
SW2(config)#vtp domain cisco
SW2(config)#vtp password cisco
SW2(config)#vtp mode client
SW2(config)#int vlan 100
SW2(config-if)#ip add 172.16.100.2 255.255.255.0
SW2(config-if)#no sh
SW2#wr
SW2#sh vlan-swi
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa1/0, Fa1/3, Fa1/4, Fa1/7
Fa1/9, Fa1/10, Fa1/11, Fa1/12
Fa1/13, Fa1/14, Fa1/15
10 VLAN0010 active
20 VLAN0020 active
100 VLAN0100 active
...
SW2(config)#ip route 0.0.0.0 0.0.0.0 172.16.1.5
SW2#wr
s3的配置信息：
s3(config)#int range f1/0 - 1
s3(config-if-range)#sw mo tr
s3(config)#vtp domain cisco
s3(config)#vtp password cisco
s3(config)#vtp mode client
s3(config)#int f1/8
s3(config-if)#sw mo ac
s3(config-if)#sw ac vlan 10
s3(config)#int vlan 100
s3(config-if)#ip add 172.16.100.3 255.255.255.0
s3(config-if)#no sh
s3(config)#ip default-gateway 172.16.100.253
s3#wr
s3#sh vlan-swi
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa1/2, Fa1/3, Fa1/4, Fa1/5
Fa1/6, Fa1/7, Fa1/9, Fa1/10
Fa1/11, Fa1/12, Fa1/13, Fa1/14
Fa1/15
10 VLAN0010 active Fa1/8
20 VLAN0020 active
s4的配置信息：
s4(config)#int range f1/1 - 2
s4(config-if-range)#sw mo tr
s4(config)#vtp domain cisco
s4(config)#vtp password cisco
s4(config)#vtp mode client
s4(config)#int f1/11
s4(config-if)#sw mo ac
s4(config-if)#sw ac vl 20
s4(config)#int vlan 100
s4(config-if)#ip add 172.16.100.4 255.255.255.0
s4(config-if)#no sh
s4#wr
s4#sh vlan-swi
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa1/0, Fa1/3, Fa1/4, Fa1/5
Fa1/6, Fa1/7, Fa1/8, Fa1/9
Fa1/10, Fa1/12, Fa1/13, Fa1/14
Fa1/15
10 VLAN0010 active
20 VLAN0020 active Fa1/11
...
s4#sh vtp status
VTP Version : 2
Configuration Revision : 4
Maximum VLANs supported locally : 36
Number of existing VLANs : 8
VTP Operating Mode : Client
VTP Domain Name : cisco
VTP Pruning Mode : Enabled
VTP V2 Mode : Disabled
VTP Traps Generation : Disabled
MD5 digest : 0x03 0xC2 0xA3 0x35 0xCA 0xAA 0x8D 0x32
Configuration last modified by 172.16.1.1 at 3-1-02 01:11:32
2）分别在SW一、SW2上配置DHCP服务（彻底一致）：
SW1(config)#ip dhcp pool vlan10
SW1(dhcp-config)#network 172.16.10.0 255.255.255.0
SW1(dhcp-config)#dns-server 202.96.134.133 8.8.8.8
SW1(dhcp-config)#default-router 172.16.10.253
SW1(config)#ip dhcp excluded-address 172.16.10.250 172.16.10.254
SW1(config)#ip dhcp pool vlan20
SW1(dhcp-config)#network 172.16.20.0 255.255.255.0
SW1(dhcp-config)#dns-server 202.96.134.133 8.8.8.8
SW1(dhcp-config)#default-router 172.16.20.253
SW1(config)#ip dhcp excluded-address 172.16.20.250 172.16.20.254
SW2#wr
SW1#sh run | sec dhcp
no ip dhcp use vrf connected
ip dhcp excluded-address 172.16.10.250 172.16.10.254
ip dhcp excluded-address 172.16.20.250 172.16.20.254
ip dhcp pool vlan10
network 172.16.10.0 255.255.255.0
dns-server 202.96.134.133 8.8.8.8
default-router 172.16.10.253
ip dhcp pool vlan20
network 172.16.20.0 255.255.255.0
dns-server 202.96.134.133 8.8.8.8
default-router 172.16.10.253
3）配置HSRP：
SW1配置：
SW1(config)#int vlan 10
SW1(config-if)#ip add 172.16.10.250 255.255.255.0
SW1(config-if)#no sh
SW1(config-if)#standby 10 ip 172.16.10.253 #配置虚拟IP
SW1(config-if)#standby 10 priority 150 #配置优先级
SW1(config-if)#standby 10 preempt #配置占先权
SW1(config-if)#standby 10 track f1/8 100 #配置端口跟踪
SW1(config-if)#standby 10 track port-channel 1 100
SW1(config)#int vlan 20
SW1(config-if)#ip add 172.16.20.250 255.255.255.0
SW1(config-if)#no sh
SW1(config-if)#standby 20 ip 172.16.20.253 #做为vlan20的备份路由器，优先级
SW1(config-if)#standby 20 preempt 默认为100，而且不须要配置端口跟踪
SW1(config-if)#int vlan 100
SW1(config-if)#ip add 172.16.100.253 255.255.255.0
SW1(config-if)#no sh
SW1#wr
SW2的配置：
SW2(config)#int vlan 10
SW2(config-if)#ip add 172.16.10.251 255.255.255.0
SW2(config-if)#no sh
SW2(config-if)#standby 10 ip 172.16.10.253
SW2(config-if)#standby 10 preempt
SW2(config)#int vlan 20
SW2(config-if)#ip add 172.16.20.251 255.255.255.0
SW2(config-if)#no sh
SW2(config-if)#standby 20 ip 172.16.20.253
SW2(config-if)#standby 20 priority 150
SW2(config-if)#standby 20 preempt
SW2(config-if)#standby 20 track f1/8 100
SW2(config-if)#standby 20 track port-channel 1 100
SW2#wr
SW1#sh standby b #在SW1上验证
P indicates configured to preempt.
|
Interface Grp Pri P State Active Standby Virtual IP
Vl10 10 150 P Active local 172.16.10.251 172.16.10.253
Vl20 20 100 P Standby 172.16.20.251 local 172.16.20.253
Vl100 10 100 Init unknown unknown 172.16.10.254
SW2#sh standby b #在SW2上验证
P indicates configured to preempt.
|
Interface Grp Pri P State Active Standby Virtual IP
Vl10 10 100 P Standby 172.16.10.250 local 172.16.10.253
Vl20 20 150 P Active local 172.16.20.250 172.16.20.253
4）配置STP，实现VLAN间的负载均衡：
SW1(config)#spanning-tree vlan 10 root primary
SW1(config)#spanning-tree vlan 20 root secondary
SW1#wr
SW2(config)#spanning-tree vlan 20 root primary
SW2(config)#spanning-tree vlan 10 root secondary
SW2#wr
在SW1上查看STP信息，可见SW1是VLAN10的根网桥，是VLAN20的备份根桥。
SW1#sh spanning-tree brief
VLAN10
Spanning tree enabled protocol ieee
Root ID Priority 8192
Address c006.1e3c.0001
This bridge is the root
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Bridge ID Priority 8192
Address c006.1e3c.0001
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Aging Time 300
Interface Designated
Name Port ID Prio Cost Sts Cost Bridge ID Port ID
-------------------- ------- ---- ----- --- ----- -------------------- -------
FastEthernet1/0 128.41 128 19 FWD 0 8192 c006.1e3c.0001 128.41
FastEthernet1/1 128.42 128 19 FWD 0 8192 c006.1e3c.0001 128.42
Port-channel1 129.65 128 12 FWD 0 8192 c006.1e3c.0001 129.65
在s3上查看，可见f1/1的端口被阻塞
s3#sh spanning-tree vlan 10
...
Port 42 (FastEthernet1/1) of VLAN10 is blocking
Port path cost 19, Port priority 128, Port Identifier 128.42.
Designated root has priority 8192, address c006.1e3c.0001
Designated bridge has priority 16384, address c007.1e3c.0001
Designated port id is 128.42, designated path cost 12
Timers: message age 3, forward delay 0, hold 0
Number of transitions to forwarding state: 0
BPDU: sent 2, received 2298
...
5）配置远程SSH管理：
SW1(config)#ip domain-name cisco
SW1(config)#username best password best1
SW1(config)#crypto key generate rsa general-keys modulus 1024
SW1(config)#ip ssh version 2
SW1(config)#enable secret cisco
SW1(config)#access-list 1 permit 172.16.20.0 0.0.0.255
SW1(config)#line vty 0 4
SW1(config-line)#login local
SW1(config-line)#access-class 1 in
SW1(config-line)#transport input ssh
SW1#wr
在客户端远程登录：
R6#ssh -l best 172.16.100.253
Password:
SW1>en
Password:
SW1#sh ip int b
Interface IP-Address OK? Method Status Protocol
FastEthernet0/0 unassigned YES unset administratively down down
FastEthernet0/1 unassigned YES unset administratively down down
FastEthernet1/0 unassigned YES unset up up
本文转自 zengwj1949 51CTO博客，原文连接:http://blog.51cto.com/zengwj1949/1925601