转载于:http://blog.csdn.net/chenlycly/article/details/52141854linux
使用下面的 route 命令能够查看 Linux 内核路由表。数据库
- # route
- Destination Gateway Genmask Flags Metric Ref Use Iface
- 192.168.0.0 * 255.255.255.0 U 0 0 0 eth0
- 169.254.0.0 * 255.255.0.0 U 0 0 0 eth0
- default 192.168.0.1 0.0.0.0 UG 0 0 0 eth0
route 命令的输出项说明缓存
输出项 说明网络
Destination |
目标网段或者主机 |
Gateway |
网关地址,”*” 表示目标是本主机所属的网络,不须要路由 |
Genmask |
网络掩码 |
Flags |
标记。一些可能的标记以下: |
|
U — 路由是活动的 |
|
H — 目标是一个主机 |
|
G — 路由指向网关 |
|
R — 恢复动态路由产生的表项 |
|
D — 由路由的后台程序动态地安装 |
|
M — 由路由的后台程序修改 |
|
! — 拒绝路由 |
Metric |
路由距离,到达指定网络所需的中转数(linux 内核中没有使用) |
Ref |
路由项引用次数(linux 内核中没有使用) |
Use |
此路由项被路由软件查找的次数 |
Iface |
该路由表项对应的输出接口 |
主机路由是路由选择表中指向单个IP地址或主机名的路由记录。主机路由的Flags字段为H。例如,在下面的示例中,本地主机经过IP地址192.168.1.1的路由器到达IP地址为10.0.0.10的主机。工具
Destination Gateway Genmask Flags Metric Ref Use Iface
----------- ------- ------- ----- ------ --- --- -----
10.0.0.10 192.168.1.1 255.255.255.255 UH 0 0 0 eth0
网络路由是表明主机能够到达的网络。网络路由的Flags字段为N。例如,在下面的示例中,本地主机将发送到网络192.19.12的数据包转发到IP地址为192.168.1.1的路由器。ui
Destination Gateway Genmask Flags Metric Ref Use Iface
----------- ------- ------- ----- ----- --- --- -----
192.19.12 192.168.1.1 255.255.255.0 UN 0 0 0 eth0
当主机不能在路由表中查找到目标主机的IP地址或网络路由时,数据包就被发送到默认路由(默认网关)上。默认路由的Flags字段为G。例如,在下面的示例中,默认路由是IP地址为192.168.1.1的路由器。spa
Destination Gateway Genmask Flags Metric Ref Use Iface
----------- ------- ------- ----- ------ --- --- -----
default 192.168.1.1 0.0.0.0 UG 0 0 0 eth0
设置和查看路由表均可以用 route 命令,设置内核路由表的命令格式是:.net
# route [add|del] [-net|-host] target [netmask Nm] [gw Gw] [[dev] If]
其中:命令行
- add : 添加一条路由规则
- del : 删除一条路由规则
- -net : 目的地址是一个网络
- -host : 目的地址是一个主机
- target : 目的网络或主机
- netmask : 目的地址的网络掩码
- gw : 路由数据包经过的网关
- dev : 为路由指定的网络接口
添加到主机的路由code
- # route add -host 192.168.1.2 dev eth0
- # route add -host 10.20.30.148 gw 10.20.30.40 #添加到10.20.30.148的网管
# route add -host 192.168.1.2 dev eth0
# route add -host 10.20.30.148 gw 10.20.30.40 #添加到10.20.30.148的网管
添加到网络的路由
- # route add -net 10.20.30.40 netmask 255.255.255.248 eth0 #添加10.20.30.40的网络
- # route add -net 10.20.30.48 netmask 255.255.255.248 gw 10.20.30.41 #添加10.20.30.48的网络
- # route add -net 192.168.1.0/24 eth1
# route add -net 10.20.30.40 netmask 255.255.255.248 eth0 #添加10.20.30.40的网络
# route add -net 10.20.30.48 netmask 255.255.255.248 gw 10.20.30.41 #添加10.20.30.48的网络
# route add -net 192.168.1.0/24 eth1
添加默认路由
- # route add default gw 192.168.1.1
# route add default gw 192.168.1.1
删除路由
- # route del -host 192.168.1.2 dev eth0:0
- # route del -host 10.20.30.148 gw 10.20.30.40
- # route del -net 10.20.30.40 netmask 255.255.255.248 eth0
- # route del -net 10.20.30.48 netmask 255.255.255.248 gw 10.20.30.41
- # route del -net 192.168.1.0/24 eth1
- # route del default gw 192.168.1.1
# route del -host 192.168.1.2 dev eth0:0
# route del -host 10.20.30.148 gw 10.20.30.40
# route del -net 10.20.30.40 netmask 255.255.255.248 eth0
# route del -net 10.20.30.48 netmask 255.255.255.248 gw 10.20.30.41
# route del -net 192.168.1.0/24 eth1
# route del default gw 192.168.1.1
在 CentOS 中默认的内核配置已经包含了路由功能,但默认并无在系统启动时启用此功能。开启 linux 的路由功能能够经过调整内核的网络参数来实现。要配置和调整内核参数可使用 sysctl 命令。例如:要开启 Linux 内核的数据包转发功能可使用以下的命令。
- # sysctl -w net.ipv4.ip_forward=1
# sysctl -w net.ipv4.ip_forward=1
这样设置以后,当前系统就能实现包转发,但下次启动计算机时将失效。为了使在下次启动计算机时仍然有效,须要将下面的行写入配置文件/etc/sysctl.conf。
- # vi /etc/sysctl.conf
- net.ipv4.ip_forward = 1
# vi /etc/sysctl.conf
net.ipv4.ip_forward = 1
用户还可使用以下的命令查看当前系统是否支持包转发。
- # sysctl net.ipv4.ip_forward
# sysctl net.ipv4.ip_forward
route 命令:
Linux系统的route命令用于显示和操做IP路由表(show / manipulate the IP routing table)。要实现两个不一样的子网之间的通讯,须要一台链接两个网络的路由器,或者同时位于两个网络的网关来实现。在Linux系统中,设置路由一般是为了解决如下问题:该Linux系统在一个局域网中,局域网中有一个网关,可以让机器访问Internet,那么就须要将这台机器的IP地址设置为Linux机器的默认路由。要注意的是,直接在命令行下执行route命令来添加路由,不会永久保存,当网卡重启或者机器重启以后,该路由就失效了;能够在/etc/rc.local中添加route命令来保证该路由设置永久有效。
1.命令格式:
route [-f] [-p] [Command [Destination] [mask Netmask] [Gateway] [metric Metric]] [if Interface]]
2.命令功能:
Route命令是用于操做基于内核ip路由表,它的主要做用是建立一个静态路由让指定一个主机或者一个网络经过一个网络接口,如eth0。当使用"add"或者"del"参数时,路由表被修改,若是没有参数,则显示路由表当前的内容。
3.命令参数:
-c 显示更多信息
-n 不解析名字
-v 显示详细的处理信息
-F 显示发送信息
-C 显示路由缓存
-f 清除全部网关入口的路由表。
-p 与 add 命令一块儿使用时使路由具备永久性。
add:添加一条新路由。
del:删除一条路由。
-net:目标地址是一个网络。
-host:目标地址是一个主机。
netmask:当添加一个网络路由时,须要使用网络掩码。
gw:路由数据包经过网关。注意,你指定的网关必须可以达到。
metric:设置路由跳数。
Command 指定您想运行的命令 (Add/Change/Delete/Print)。
Destination 指定该路由的网络目标。
mask Netmask 指定与网络目标相关的网络掩码(也被称做子网掩码)。
Gateway 指定网络目标定义的地址集和子网掩码能够到达的前进或下一跃点 IP 地址。
metric Metric 为路由指定一个整数成本值标(从 1 至 9999),当在路由表(与转发的数据包目标地址最匹配)的多个路由中进行选择时可使用。
if Interface 为能够访问目标的接口指定接口索引。若要得到一个接口列表和它们相应的接口索引,使用 route print 命令的显示功能。可使用十进制或十六进制值进行接口索引。
4.使用实例:
实例1:显示当前路由
命令:
route
route -n
输出:
- [root@localhost ~]# route
- Kernel IP routing table
- Destination Gateway Genmask Flags Metric Ref Use Iface
- 192.168.120.0 * 255.255.255.0 U 0 0 0 eth0
- e192.168.0.0 192.168.120.1 255.255.0.0 UG 0 0 0 eth0
- 10.0.0.0 192.168.120.1 255.0.0.0 UG 0 0 0 eth0
- default 192.168.120.240 0.0.0.0 UG 0 0 0 eth0
- [root@localhost ~]# route -n
- Kernel IP routing table
- Destination Gateway Genmask Flags Metric Ref Use Iface
- 192.168.120.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0
- 192.168.0.0 192.168.120.1 255.255.0.0 UG 0 0 0 eth0
- 10.0.0.0 192.168.120.1 255.0.0.0 UG 0 0 0 eth0
- 0.0.0.0 192.168.120.240 0.0.0.0 UG 0 0 0 eth0
[root@localhost ~]# route
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
192.168.120.0 * 255.255.255.0 U 0 0 0 eth0
e192.168.0.0 192.168.120.1 255.255.0.0 UG 0 0 0 eth0
10.0.0.0 192.168.120.1 255.0.0.0 UG 0 0 0 eth0
default 192.168.120.240 0.0.0.0 UG 0 0 0 eth0
[root@localhost ~]# route -n
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
192.168.120.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0
192.168.0.0 192.168.120.1 255.255.0.0 UG 0 0 0 eth0
10.0.0.0 192.168.120.1 255.0.0.0 UG 0 0 0 eth0
0.0.0.0 192.168.120.240 0.0.0.0 UG 0 0 0 eth0
说明:
第一行表示主机所在网络的地址为192.168.120.0,若数据传送目标是在本局域网内通讯,则可直接经过eth0转发数据包;
第四行表示数据传送目的是访问Internet,则由接口eth0,将数据包发送到网关192.168.120.240
其中Flags为路由标志,标记当前网络节点的状态。
Flags标志说明:
U Up表示此路由当前为启动状态
H Host,表示此网关为一主机
G Gateway,表示此网关为一路由器
R Reinstate Route,使用动态路由从新初始化的路由
D Dynamically,此路由是动态性地写入
M Modified,此路由是由路由守护程序或导向器动态修改
! 表示此路由当前为关闭状态
备注:
route -n (-n 表示不解析名字,列出速度会比route 快)
实例2:添加网关/设置网关
命令:
route add -net 224.0.0.0 netmask 240.0.0.0 dev eth0
输出:
- [root@localhost ~]# route add -net 224.0.0.0 netmask 240.0.0.0 dev eth0
- [root@localhost ~]# route
- Kernel IP routing table
- Destination Gateway Genmask Flags Metric Ref Use Iface
- 192.168.120.0 * 255.255.255.0 U 0 0 0 eth0
- 192.168.0.0 192.168.120.1 255.255.0.0 UG 0 0 0 eth0
- 10.0.0.0 192.168.120.1 255.0.0.0 UG 0 0 0 eth0
- 224.0.0.0 * 240.0.0.0 U 0 0 0 eth0
- default 192.168.120.240 0.0.0.0 UG 0 0 0 eth0
[root@localhost ~]# route add -net 224.0.0.0 netmask 240.0.0.0 dev eth0
[root@localhost ~]# route
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
192.168.120.0 * 255.255.255.0 U 0 0 0 eth0
192.168.0.0 192.168.120.1 255.255.0.0 UG 0 0 0 eth0
10.0.0.0 192.168.120.1 255.0.0.0 UG 0 0 0 eth0
224.0.0.0 * 240.0.0.0 U 0 0 0 eth0
default 192.168.120.240 0.0.0.0 UG 0 0 0 eth0
[root@localhost ~]#
说明:
增长一条 到达244.0.0.0的路由
实例3:屏蔽一条路由
命令:
route add -net 224.0.0.0 netmask 240.0.0.0 reject
输出:
- [root@localhost ~]# route add -net 224.0.0.0 netmask 240.0.0.0 reject
- [root@localhost ~]# route
- Kernel IP routing table
- Destination Gateway Genmask Flags Metric Ref Use Iface
- 192.168.120.0 * 255.255.255.0 U 0 0 0 eth0
- 192.168.0.0 192.168.120.1 255.255.0.0 UG 0 0 0 eth0
- 10.0.0.0 192.168.120.1 255.0.0.0 UG 0 0 0 eth0
- 224.0.0.0 - 240.0.0.0 ! 0 - 0 -
- 224.0.0.0 * 240.0.0.0 U 0 0 0 eth0
- default 192.168.120.240 0.0.0.0 UG 0 0 0 eth0
[root@localhost ~]# route add -net 224.0.0.0 netmask 240.0.0.0 reject
[root@localhost ~]# route
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
192.168.120.0 * 255.255.255.0 U 0 0 0 eth0
192.168.0.0 192.168.120.1 255.255.0.0 UG 0 0 0 eth0
10.0.0.0 192.168.120.1 255.0.0.0 UG 0 0 0 eth0
224.0.0.0 - 240.0.0.0 ! 0 - 0 -
224.0.0.0 * 240.0.0.0 U 0 0 0 eth0
default 192.168.120.240 0.0.0.0 UG 0 0 0 eth0
说明:
增长一条屏蔽的路由,目的地址为 224.x.x.x 将被拒绝
实例4:删除路由记录
命令:
route del -net 224.0.0.0 netmask 240.0.0.0
route del -net 224.0.0.0 netmask 240.0.0.0 reject
输出:
- [root@localhost ~]# route
- Kernel IP routing table
- Destination Gateway Genmask Flags Metric Ref Use Iface
- 192.168.120.0 * 255.255.255.0 U 0 0 0 eth0
- 192.168.0.0 192.168.120.1 255.255.0.0 UG 0 0 0 eth0
- 10.0.0.0 192.168.120.1 255.0.0.0 UG 0 0 0 eth0
- 224.0.0.0 - 240.0.0.0 ! 0 - 0 -
- 224.0.0.0 * 240.0.0.0 U 0 0 0 eth0
- default 192.168.120.240 0.0.0.0 UG 0 0 0 eth0
- [root@localhost ~]# route del -net 224.0.0.0 netmask 240.0.0.0
- [root@localhost ~]# route
- Kernel IP routing table
- Destination Gateway Genmask Flags Metric Ref Use Iface
- 192.168.120.0 * 255.255.255.0 U 0 0 0 eth0
- 192.168.0.0 192.168.120.1 255.255.0.0 UG 0 0 0 eth0
- 10.0.0.0 192.168.120.1 255.0.0.0 UG 0 0 0 eth0
- 224.0.0.0 - 240.0.0.0 ! 0 - 0 -
- default 192.168.120.240 0.0.0.0 UG 0 0 0 eth0
- [root@localhost ~]# route del -net 224.0.0.0 netmask 240.0.0.0 reject
- [root@localhost ~]# route
- Kernel IP routing table
- Destination Gateway Genmask Flags Metric Ref Use Iface
- 192.168.120.0 * 255.255.255.0 U 0 0 0 eth0
- 192.168.0.0 192.168.120.1 255.255.0.0 UG 0 0 0 eth0
- 10.0.0.0 192.168.120.1 255.0.0.0 UG 0 0 0 eth0
- default 192.168.120.240 0.0.0.0 UG 0 0 0 eth0
- [root@localhost ~]#
[root@localhost ~]# route
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
192.168.120.0 * 255.255.255.0 U 0 0 0 eth0
192.168.0.0 192.168.120.1 255.255.0.0 UG 0 0 0 eth0
10.0.0.0 192.168.120.1 255.0.0.0 UG 0 0 0 eth0
224.0.0.0 - 240.0.0.0 ! 0 - 0 -
224.0.0.0 * 240.0.0.0 U 0 0 0 eth0
default 192.168.120.240 0.0.0.0 UG 0 0 0 eth0
[root@localhost ~]# route del -net 224.0.0.0 netmask 240.0.0.0
[root@localhost ~]# route
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
192.168.120.0 * 255.255.255.0 U 0 0 0 eth0
192.168.0.0 192.168.120.1 255.255.0.0 UG 0 0 0 eth0
10.0.0.0 192.168.120.1 255.0.0.0 UG 0 0 0 eth0
224.0.0.0 - 240.0.0.0 ! 0 - 0 -
default 192.168.120.240 0.0.0.0 UG 0 0 0 eth0
[root@localhost ~]# route del -net 224.0.0.0 netmask 240.0.0.0 reject
[root@localhost ~]# route
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
192.168.120.0 * 255.255.255.0 U 0 0 0 eth0
192.168.0.0 192.168.120.1 255.255.0.0 UG 0 0 0 eth0
10.0.0.0 192.168.120.1 255.0.0.0 UG 0 0 0 eth0
default 192.168.120.240 0.0.0.0 UG 0 0 0 eth0
[root@localhost ~]#
说明:
实例5:删除和添加设置默认网关
命令:
route del default gw 192.168.120.240
route add default gw 192.168.120.240
输出:
- [root@localhost ~]# route del default gw 192.168.120.240
- [root@localhost ~]# route
- Kernel IP routing table
- Destination Gateway Genmask Flags Metric Ref Use Iface
- 192.168.120.0 * 255.255.255.0 U 0 0 0 eth0
- 192.168.0.0 192.168.120.1 255.255.0.0 UG 0 0 0 eth0
- 10.0.0.0 192.168.120.1 255.0.0.0 UG 0 0 0 eth0
- [root@localhost ~]# route add default gw 192.168.120.240
- [root@localhost ~]# route
- Kernel IP routing table
- Destination Gateway Genmask Flags Metric Ref Use Iface
- 192.168.120.0 * 255.255.255.0 U 0 0 0 eth0
- 192.168.0.0 192.168.120.1 255.255.0.0 UG 0 0 0 eth0
- 10.0.0.0 192.168.120.1 255.0.0.0 UG 0 0 0 eth0
- default 192.168.120.240 0.0.0.0 UG 0 0 0 eth0
- [root@localhost ~]#
[root@localhost ~]# route del default gw 192.168.120.240
[root@localhost ~]# route
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
192.168.120.0 * 255.255.255.0 U 0 0 0 eth0
192.168.0.0 192.168.120.1 255.255.0.0 UG 0 0 0 eth0
10.0.0.0 192.168.120.1 255.0.0.0 UG 0 0 0 eth0
[root@localhost ~]# route add default gw 192.168.120.240
[root@localhost ~]# route
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
192.168.120.0 * 255.255.255.0 U 0 0 0 eth0
192.168.0.0 192.168.120.1 255.255.0.0 UG 0 0 0 eth0
10.0.0.0 192.168.120.1 255.0.0.0 UG 0 0 0 eth0
default 192.168.120.240 0.0.0.0 UG 0 0 0 eth0
[root@localhost ~]#
- 显示如今全部路由
-
- #route -n
-
- root@Ubuntu:~# route
-
- Kernel IP routing table
-
- Destination Gateway Genmask Flags Metric Ref Use Iface
-
- 10.147.9.0 * 255.255.255.0 U 1 0 0 eth0
-
- 192.168.1.0 * 255.255.255.0 U 2 0 0 wlan0
-
- 192.168.122.0 * 255.255.255.0 U 0 0 0 virbr0
-
- link-local * 255.255.0.0 U 1000 0 0 eth0
-
- 192.168.0.0 192.168.1.1 255.255.0.0 UG 0 0 0 wlan0
-
- default 10.147.9.1 0.0.0.0 UG 0 0 0 eth0
-
- root@Ubuntu:~#
-
- 结果是自上而下, 就是说, 哪条在前面, 哪条就有优先, 前面都没有, 就用最后一条default
-
- 举例, 添加一条路由(发往192.168.62这个网段的所有要通过网关192.168.1.1)
-
- route add -net 192.168.62.0 netmask 255.255.255.0 gw 192.168.1.1
-
- 删除一条路由
-
- route del -net 192.168.122.0 netmask 255.255.255.0
-
- 删除的时候不用写网关
-
- linux下添加路由的方法:
-
- 一:使用 route 命令添加
-
- 使用route 命令添加的路由,机器重启或者网卡重启后路由就失效了,方法:
-
-
-
- # route add –host 192.168.168.110 dev eth0
-
- # route add –host 192.168.168.119 gw 192.168.168.1
-
-
-
- # route add –net IP netmask MASK eth0
-
- # route add –net IP netmask MASK gw IP
-
- # route add –net IP/24 eth1
-
-
-
- # route add default gw IP
-
-
-
- # route del –host 192.168.168.110 dev eth0
-
- 二:在linux下设置永久路由的方法:
-
- 1.在/etc/rc.local里添加
-
- 方法:
-
- route add -net 192.168.3.0/24 dev eth0
-
- route add -net 192.168.2.0/24 gw 192.168.3.254
-
- 2.在/etc/sysconfig/network里添加到末尾
-
- 方法:GATEWAY=gw-ip 或者 GATEWAY=gw-dev
-
- 3./etc/sysconfig/static-router :
-
- any net x.x.x.x/24 gw y.y.y.y
-
-
- ------------------------------------------------------------------------------------------
- -- Route命令的正确用法
- 使用 Route 命令行工具查看并编辑计算机的 IP 路由表。Route 命令和语法以下所示:
- route [-f] [-p] [Command [Destination] [mask Netmask] [Gateway] [metric Metric]] [if Interface]]
- -f 清除全部网关入口的路由表。
- -p 与 add 命令一块儿使用时使路由具备永久性。
- Command 指定您想运行的命令 (Add/Change/Delete/Print)。
- Destination 指定该路由的网络目标。
- mask Netmask 指定与网络目标相关的网络掩码(也被称做子网掩码)。
- Gateway 指定网络目标定义的地址集和子网掩码能够到达的前进或下一跃点 IP 地址。
- metric Metric 为路由指定一个整数成本值标(从 1 至 ArrayArrayArrayArray),当在路由表(与转发的数据包目标地址最匹配)的多个路由中进行选择时可使用。
- if Interface 为能够访问目标的接口指定接口索引。若要得到一个接口列表和它们相应的接口索引,使用 route print 命令的显示功能。可使用十进制或十六进制值进行接口索引。
- /? 在命令提示符处显示帮助。
- 示例
- 若要显示 IP 路由表的所有内容,请键入:
- route print
- 若要显示以 10. 起始的 IP 路由表中的路由,请键入:
- route print 10.*
- 若要添加带有 1Array2.168.12.1 默认网关地址的默认路由,请键入:
- route add 0.0.0.0 mask 0.0.0.0 1Array2.168.12.1
- 若要向带有 255.255.0.0 子网掩码和 10.27.0.1 下一跃点地址的 10.41.0.0 目标中添加一个路由,请键入:
- route add 10.41.0.0 mask 255.255.0.0 10.27.0.1
- 若要向带有 255.255.0.0 子网掩码和 10.27.0.1 下一跃点地址的 10.41.0.0 目标中添加一个永久路由,请键入:
- route -p add 10.41.0.0 mask 255.255.0.0 10.27.0.1
- 若要向带有 255.255.0.0 子网掩码、10.27.0.1 下一跃点地址且其成本值标为 7 的 10.41.0.0 目标中添加一个路由,请键入:
- route add 10.41.0.0 mask 255.255.0.0 10.27.0.1 metric 7
- 若要向带有 255.255.0.0 子网掩码、10.27.0.1 下一跃点地址且使用 0x3 接口索引的 10.41.0.0 目标中添加一个路由,请键入:
- route add 10.41.0.0 mask 255.255.0.0 10.27.0.1 if 0x3
- 若要删除到带有 255.255.0.0 子网掩码的 10.41.0.0 目标的路由,请键入:
- route delete 10.41.0.0 mask 255.255.0.0
- 若要删除以 10. 起始的 IP 路由表中的全部路由,请键入:
- route delete 10.*
- 若要将带有 10.41.0.0 目标和 255.255.0.0 子网掩码的下一跃点地址从 10.27.0.1 修改成 10.27.0.25,请键入:
- route change 10.41.0.0 mask 255.255.0.0 10.27.0.25
-
- -------------------------------------------------------------------------
- 首先,先了解传统的网络配置命令:
- 1. 使用ifconfig命令配置并查看网络接口状况
- 示例1: 配置eth0的IP,同时激活设备:
- # ifconfig eth0 192.168.4.1 netmask 255.255.255.0 up
- 示例2: 配置eth0别名设备 eth0:1 的IP,并添加路由
- # ifconfig eth0:1 192.168.4.2
- # route add –host 192.168.4.2 dev eth0:1
- 示例3:激活(禁用)设备
- # ifconfig eth0:1 up(down)
- 示例4:查看全部(指定)网络接口配置
- # ifconfig (eth0)
- 2. 使用route 命令配置路由表
- 示例1:添加到主机路由
- # route add –host 192.168.4.2 dev eth0:1
- # route add –host 192.168.4.1 gw 192.168.4.250
- 示例2:添加到网络的路由
- # route add –net IP netmask MASK eth0
- # route add –net IP netmask MASK gw IP
- # route add –net IP/24 eth1
- 示例3:添加默认网关
- # route add default gw IP
- 示例4:删除路由
- # route del –host 192.168.4.1 dev eth0:1
- 示例5:查看路由信息
- # route 或 route -n (-n 表示不解析名字,列出速度会比route 快)
- 3.ARP 管理命令
- 示例1:查看ARP缓存
- # arp
- 示例2: 添加
- # arp –s IP MAC
- 示例3: 删除
- # arp –d IP
- 4. ip是iproute2软件包里面的一个强大的网络配置工具,它可以替代一些传统的网络管理工具。例如:ifconfig、route等,
- 上面的示例彻底能够用下面的ip命令实现,并且ip命令能够实现更多的功能.下面介绍一些示例:
- 4.0 ip命令的语法
- ip命令的用法以下:
- ip [OPTIONS] OBJECT [COMMAND [ARGUMENTS]]
- 4.1 ip link set--改变设备的属性. 缩写:set、s
- 示例1:up/down 起动/关闭设备。
- # ip link set dev eth0 up
- 这个等于传统的 # ifconfig eth0 up(down)
- 示例2:改变设备传输队列的长度。
- 参数:txqueuelen NUMBER或者txqlen NUMBER
- # ip link set dev eth0 txqueuelen 100
- 示例3:改变网络设备MTU(最大传输单元)的值。
- # ip link set dev eth0 mtu 1500
- 示例4: 修改网络设备的MAC地址。
- 参数: address LLADDRESS
- # ip link set dev eth0 address 00:01:4f:00:15:f1
- 4.2 ip link show--显示设备属性. 缩写:show、list、lst、sh、ls、l
- -s选项出现两次或者更屡次,ip会输出更为详细的错误信息统计。
- 示例:
- # ip -s -s link ls eth0
- eth0: mtu 1500 qdisc cbq qlen 100
- link/ether 00:a0:cc:66:18:78 brd ff:ff:ff:ff:ff:ff
- RX: bytes packets errors dropped overrun mcast
- 2449949362 2786187 0 0 0 0
- RX errors: length crc fifo missed
- 0 0 0 0 0
- TX: bytes packets errors dropped carrier collsns
- 178558497 1783946 332 0 332 35172
- TX errors: aborted fifo window heartbeat
- 0 0 0 332
- 这个命令等于传统的 ifconfig eth0
- 5.1 ip address add--添加一个新的协议地址. 缩写:add、a
- 示例1:为每一个地址设置一个字符串做为标签。为了和Linux-2.0的网络别名兼容,这个字符串必须以设备名开头,接着一个冒号,
- # ip addr add local 192.168.4.1/28 brd + label eth0:1 dev eth0
- 示例2: 在以太网接口eth0上增长一个地址192.168.20.0,掩码长度为24位(155.155.155.0),标准广播地址,标签为eth0:Alias:
- # ip addr add 192.168.4.2/24 brd + dev eth1 label eth1:1
- 这个命令等于传统的: ifconfig eth1:1 192.168.4.2
- 5.2 ip address delete--删除一个协议地址. 缩写:delete、del、d
- # ip addr del 192.168.4.1/24 brd + dev eth0 label eth0:Alias1
- 5.3 ip address show--显示协议地址. 缩写:show、list、lst、sh、ls、l
- # ip addr ls eth0
- 5.4.ip address flush--清除协议地址. 缩写:flush、f
- 示例1 : 删除属于私网10.0.0.0/8的全部地址:
- # ip -s -s a f to 10/8
- 示例2 : 取消全部以太网卡的IP地址
- # ip -4 addr flush label "eth0"
- 6. ip neighbour--neighbour/arp表管理命令
- 缩写 neighbour、neighbor、neigh、n
- 命令 add、change、replace、delete、fulsh、show(或者list)
- 6.1 ip neighbour add -- 添加一个新的邻接条目
- ip neighbour change--修改一个现有的条目
- ip neighbour replace--替换一个已有的条目
- 缩写:add、a;change、chg;replace、repl
- 示例1: 在设备eth0上,为地址10.0.0.3添加一个permanent ARP条目:
- # ip neigh add 10.0.0.3 lladdr 0:0:0:0:0:1 dev eth0 nud perm
- 示例2:把状态改成reachable
- # ip neigh chg 10.0.0.3 dev eth0 nud reachable
- 6.2.ip neighbour delete--删除一个邻接条目
- 示例1:删除设备eth0上的一个ARP条目10.0.0.3
- # ip neigh del 10.0.0.3 dev eth0
- 6.3.ip neighbour show--显示网络邻居的信息. 缩写:show、list、sh、ls
- 示例1: # ip -s n ls 193.233.7.254
- 193.233.7.254. dev eth0 lladdr 00:00:0c:76:3f:85 ref 5 used 12/13/20 nud reachable
- 6.4.ip neighbour flush--清除邻接条目. 缩写:flush、f
- 示例1: (-s 能够显示详细信息)
- # ip -s -s n f 193.233.7.254
- 7. 路由表管理
- 7.1.缩写 route、ro、r
- 7.2.路由表
- 从Linux-2.2开始,内核把路由概括到许多路由表中,这些表都进行了编号,编号数字的范围是1到255。另外,
- 为了方便,还能够在/etc/iproute2/rt_tables中为路由表命名。
- 默认状况下,全部的路由都会被插入到表main(编号254)中。在进行路由查询时,内核只使用路由表main。
- 7.3.ip route add -- 添加新路由
- ip route change -- 修改路由
- ip route replace -- 替换已有的路由
- 缩写:add、a;change、chg;replace、repl
- 示例1: 设置到网络10.0.0/24的路由通过网关193.233.7.65
- # ip route add 10.0.0/24 via 193.233.7.65
- 示例2: 修改到网络10.0.0/24的直接路由,使其通过设备dummy
- # ip route chg 10.0.0/24 dev dummy
- 示例3: 实现链路负载平衡.加入缺省多路径路由,让ppp0和ppp1分担负载(注意:scope值并不是必需,它只不过是告诉内核,
- 这个路由要通过网关而不是直连的。实际上,若是你知道远程端点的地址,使用via参数来设置就更好了)。
- # ip route add default scope global nexthop dev ppp0 nexthop dev ppp1
- # ip route replace default scope global nexthop dev ppp0 nexthop dev ppp1
- 示例4: 设置NAT路由。在转发来自192.203.80.144的数据包以前,先进行网络地址转换,把这个地址转换为193.233.7.83
- # ip route add nat 192.203.80.142 via 193.233.7.83
- 示例5: 实现数据包级负载平衡,容许把数据包随机从多个路由发出。weight 能够设置权重.
- # ip route replace default equalize nexthop via 211.139.218.145 dev eth0 weight 1 nexthop via 211.139.218.145 dev eth1 weight 1
- 7.4.ip route delete-- 删除路由
- 缩写:delete、del、d
- 示例1:删除上一节命令加入的多路径路由
- # ip route del default scope global nexthop dev ppp0 nexthop dev ppp1
- 7.5.ip route show -- 列出路由
- 缩写:show、list、sh、ls、l
- 示例1: 计算使用gated/bgp协议的路由个数
- # ip route ls proto gated/bgp |wc
- 1413 9891 79010
- 示例2: 计算路由缓存里面的条数,因为被缓存路由的属性可能大于一行,以此须要使用-o选项
- # ip -o route ls cloned |wc
- 159 2543 18707
- 示例3: 列出路由表TABLEID里面的路由。缺省设置是table main。TABLEID或者是一个真正的路由表ID或者是/etc/iproute2/rt_tables文件定义的字符串,
- 或者是如下的特殊值:
- all -- 列出全部表的路由;
- cache -- 列出路由缓存的内容。
- ip ro ls 193.233.7.82 tab cache
- 示例4: 列出某个路由表的内容
- # ip route ls table fddi153
- 示例5: 列出默认路由表的内容
- # ip route ls
- 这个命令等于传统的: route
- 7.6.ip route flush -- 擦除路由表
- 示例1: 删除路由表main中的全部网关路由(示例:在路由监控程序挂掉以后):
- # ip -4 ro flush scope global type unicast
- 示例2:清除全部被克隆出来的IPv6路由:
- # ip -6 -s -s ro flush cache
- 示例3: 在gated程序挂掉以后,清除全部的BGP路由:
- # ip -s ro f proto gated/bgp
- 示例4: 清除全部ipv4路由cache
- # ip route flush cache
- *** IPv4 routing cache is flushed.
- 7.7 ip route get -- 得到单个路由 .缩写:get、g
- 使用这个命令能够得到到达目的地址的一个路由以及它的确切内容。
- ip route get命令和ip route show命令执行的操做是不一样的。ip route show命令只是显示现有的路由,而ip route get命令在必要时会派生出新的路由。
- 示例1: 搜索到193.233.7.82的路由
- # ip route get 193.233.7.82
- 193.233.7.82 dev eth0 src 193.233.7.65 realms inr.ac cache mtu 1500 rtt 300
- 示例2: 搜索目的地址是193.233.7.82,来自193.233.7.82,从eth0设备到达的路由(这条命令会产生一条很是有意思的路由,这是一条到193.233.7.82的回环路由)
- # ip r g 193.233.7.82 from 193.233.7.82 iif eth0
- 193.233.7.82 from 193.233.7.82 dev eth0 src 193.233.7.65 realms inr.ac/inr.ac
- cache
- mtu 1500 rtt 300 iif eth0
- 8. ip route -- 路由策略数据库管理命令
- 命令
- add、delete、show(或者list)
- 注意:策略路由(policy routing)不等于路由策略(rouing policy)。
- 在某些状况下,咱们不仅是须要经过数据包的目的地址决定路由,可能还须要经过其余一些域:源地址、IP协议、传输层端口甚至数据包的负载。
- 这就叫作:策略路由(policy routing)。
- 8.1. ip rule add -- 插入新的规则
- ip rule delete -- 删除规则
- 缩写:add、a;delete、del、d
- 示例1: 经过路由表inr.ruhep路由来自源地址为192.203.80/24的数据包
- ip ru add from 192.203.80/24 table inr.ruhep prio 220
- 示例2:把源地址为193.233.7.83的数据报的源地址转换为192.203.80.144,并经过表1进行路由
- ip ru add from 193.233.7.83 nat 192.203.80.144 table 1 prio 320
- 示例3:删除无用的缺省规则
- ip ru del prio 32767
- 8.2. ip rule show -- 列出路由规则
- 缩写:show、list、sh、ls、l
- 示例1: # ip ru ls
- 0: from all lookup local
- 32762: from 192.168.4.89 lookup fddi153
- 32764: from 192.168.4.88 lookup fddi153
- 32766: from all lookup main
- 32767: from all lookup 253
- 9. ip maddress -- 多播地址管理
- 缩写:show、list、sh、ls、l
- 9.1.ip maddress show -- 列出多播地址
- 示例1: # ip maddr ls dummy
- 9.2. ip maddress add -- 加入多播地址
- ip maddress delete -- 删除多播地址
- 缩写:add、a;delete、del、d
- 使用这两个命令,咱们能够添加/删除在网络接口上监听的链路层多播地址。这个命令只能管理链路层地址。
- 示例1: 增长 # ip maddr add 33:33:00:00:00:01 dev dummy
- 示例2: 查看 # ip -O maddr ls dummy
- 2: dummy
- link 33:33:00:00:00:01 users 2 static
- link 01:00:5e:00:00:01
- 示例3: 删除 # ip maddr del 33:33:00:00:00:01 dev dummy
- 10.ip mroute -- 多播路由缓存管理
- 10.1. ip mroute show -- 列出多播路由缓存条目
- 缩写:show、list、sh、ls、l
- 示例1:查看 # ip mroute ls
- (193.232.127.6, 224.0.1.39) Iif: unresolved
- (193.232.244.34, 224.0.1.40) Iif: unresolved
- (193.233.7.65, 224.66.66.66) Iif: eth0 Oifs: pimreg
- 示例2:查看 # ip -s mr ls 224.66/16
- (193.233.7.65, 224.66.66.66) Iif: eth0 Oifs: pimreg
- 9383 packets, 300256 bytes
- 11. ip tunnel -- 通道配置
- 缩写
- tunnel、tunl
- 11.1.ip tunnel add -- 添加新的通道
- ip tunnel change -- 修改现有的通道
- ip tunnel delete -- 删除一个通道
- 缩写:add、a;change、chg;delete、del、d
- 示例1:创建一个点对点通道,最大TTL是32
- # ip tunnel add Cisco mode sit remote 192.31.7.104 local 192.203.80.1 ttl 32
- 11.2.ip tunnel show -- 列出现有的通道
- 缩写:show、list、sh、ls、l
- 示例1: # ip -s tunl ls Cisco
- 12. ip monitor和rtmon -- 状态监视
- ip命令能够用于连续地监视设备、地址和路由的状态。这个命令选项的格式有点不一样,命令选项的名字叫作monitor,接着是操做对象:
- ip monitor [ file FILE ] [ all | OBJECT-LIST ]
- 示例1: # rtmon file /var/log/rtmon.log
- 示例2: # ip monitor file /var/log/rtmon.log r